Our products

Prather stainless steel strut with 3/16" needle bearings fitted. & mounting bracket. For setups 3.5cc to 15cc 

Speedmaster 3/16" soldered flange brass bushing for 3/16" struts

Speedmaster 1/4" soldered flange brass bushing for struts

Speedmaster brass 3/16" bushing with flange.

USA import SPEEDMASTER Brass sleave flared bushings for the stinger drive units. 3/16 & 1/4". These are brass sleaves, crossed drilled to hold the lubricating grease."

Speedmaster/ high quality skeg strut assembly with mounting bracket.  Required bearings to be fitted

SPEEDMASTER CNC machined strut blade only with skeg and 1/4" sleeve bearings fitted.
SPDS-013-SK Large Skeg Strut Assy. With bracket, mounting bolts etc. and bearings fitted  £35.95

This is the NEW heavy duty HIGH QUALITY version of the stinger units from Speedmaster, now with a 3 hole mounting bracket, suitable for the larger petrol engines from 23cc up to 35cc. The unit takes a 1/4 flexi shaft and is adjustable vertically and shaft angle. Also suitable for 15cc + glow motors.
"

An adjustable drive unit suitable .21 - .65 engines using a 3/16 flexi shaft. Stinger length is 80mm (3.25") Also suitable for fast electrics and the OMRA "Z" class boats.

A modification we can make is to replace the brass sleave bearing with Lead teflons."

The SPEEDMASTER Stinger adjustable strut is CNC machined from high grade aircraft aluminum. For use with 1/4" shafts. Strut is adjustable vertically on the transom as is the shaft angle. The unit is available with 1/4" sleave bearings instead of the standard brass bushing, as a modification if required.

The transom mounting has a 3 holes mounting bracket.

 1/4" Stinger drive VS3 Adjustable 125mm long. Very strong CNC machined aluminium drive unit with adjustment for shaft angle and fitted with lead teflon bushes. For all 1/4" flexis shafts, welded type..

1/4" Stinger drive VS3 Adjustable 105mm to 125mm long. Very strong CNC machined aluminium drive unit with adjustment for shaft angle and stinger length and fitted with lead teflon bushes. For all 1/4"flexis, welded type..

RC adjustable angle 1/4 Stinger drive . Very strong CNC machined aluminium drive unit with radio adjustment for shaft angle. Fitted with lead teflon bushes. To be used with 1/4"flexis, welded type

The famous OCTURA Strudder unit fitted with 3/16" bearings and nose piece to take the 9/32" brass prop tube.

A 55mm Ali bar is supplied to offset the rudder. 

This is the famous and original outdrive unit from OCTURA. It is ideal for monos and cats and allows the strut to have greater adjustment that the use of a stinger drive. For use with engines from 6.5cc up to 35cc. The unit comes with an extuded allumium transom bracket for extra strength, a rudder with integral water pick up and the extruded profiled strut blade fitted with 1/4" lead teflon sleave bearings fitted in a reducer bushing and a nose piece to take a 11/32" brass prop tube.
A 55mm bar is supplied to enable the rudder to be offset to the side of the prop.

Aeromarine ali strut and bracket with fixing nuts and bolts

Aeromarine strut assembly complete with nose piece, reducer and 1/4" sleeve bearings fitted

This is the exploded view of the standard profiled mono, cat & hydro strut for use with IC motors from 3.5cc up to 11cc. Fitted with nose piece, reducer and 3/16" lead teflon sleave bearings. Unit comes assembled.
Blade depth 3.75", width 1.25"


"

The standard profiled alluminun strut blade for engines from 3.5cc up to 26cc including petrol powered craft. Fitted with nose piece, reducer & 1/4" lead teflon sleeve bearings.
Blade depth 3.75", width 1.25"

Surface drive hydro strut with flat bottom complete nose piece & reducer to take sleave bearings.
State wether 1/4" or 3/16" bearings required when ordering

Octura cast stainless steel strut & skeg. Complete with nose piece reducer and either 1/4" or 3/16" LT sleave bearings. Please state which required when ordering"

A heavy duty cast Stainless steel strut blade with skeg which will help to protect your prop from serious damage. The strut comes fitted with a nose piece, reducer and either 3/16 or 1/4" lead teflon bearings.
Please specify 1/4" or 3/16" bearings when ordering

This cast BeCu strut from Octura is designed for use with fast electrics but is also very suitable for the .10, .12 etc motors, and could be considered for, 3.5cc motors.
It comes with 3/16" bearings fitted and a nose piece into which .130" teflon fits.

Small cast strut blade with skeg with 3/16 bearings. Ideal for electrics and motors up to .18. Could also be used for 3.5cc motors. Nose piece takes the .150" teflon tubing."

OCTURA  strut suitable for fast electrics, Z" class and motors up to .45. Cast in BeCu with 3/16" sleave bearings fitted. A brass nose piece to take .130 or .150" teflon can be fitted if required. extra £1.50

Octura brass connecting ferrule for connecting 1/4" cable to 3/16" stub shaft

OCTURA Brass connecting ferrule for connecting 1/4" cable to 1/4" stub shaft.
Cable has to be soldered to the ferrule which is then fitted to the stub shaft with 2 grub screws.

OCTURA 1/8" lead Teflon sleeve bushing

AEROMARINE stainless reducer bushings are bored to accept 3/16" led teflon bearings. Precision machined,