Our products

Octura stainless steel 3/16" long prop shaft with flats machined for location of drive dog and connecting ferrule

Stainless steel 2" x 1/8" prop shaft bored for .098" cable. Shaft used for the 1/8" bored props.

Octura OCGCSS4 Stainless steel stepped 4mm to 1/8" stub shaft complete with drive dog, washer and brass tail nut. Can be fitted with .130" cable to make a complete flexi shaft.
Stub shaft only £3.95

OCTURA OCGCSL 3.25" s/s stub shaft, 4mm stepped up to 3/16". Complete with drive dog, washer and retaining nut.  A replacement shaft for any 4mm bearing struts such as the Graupner or Kyosho drives allowing a 3/16" bore prop to be used.  Can also be fitted with .130 or .150 cable to make a complete flexi shaft.

5mm Stainless steel stub shaft 2.5" long. Please specify actual length required and hole size for shaft.

Stainless steel 4mm stubshaft,  threaded for 15mm and bored to take .130 cable.
Can also be bored to take .150" cable. Joining has to be done by silver soldering only for the .150 cable after the cable has been modified. Not a job for the inexperienced.

Longer or shorter lengths can also be supplied. State when ordering

Octura stainless steel 3/16" O.D. x 2.25" long stub shaft down to 1/8" threaded 5-40. Can be bored to take .062" .130" .150" flexi cable.

Stub shaft OAL. 2.25" x 3/16" s/s stub shaft with 15mm of 4mm thread included in length. Drilled .150" (3.8mm)Octura flexi cable.
Longer length available

Stainless steel Stub shaft OAL. 2.25" x 3/16" with 15mm x 4mm thread included in length. Drilled to take .130" (3.2mm) cable. Longer length available

A stainless steel 3/16" x 3.25" with 15mm of 4mm thread and drilled to take .150" cable

Stainless steel 3/16" x 2.5" stub shaft with a 5mm thread. Shaft is counter bored to take either .130" or .150" flexi cable.  Shaft can also be bored for 2mm and 1/16" wire drives.

Longer or shorter lengths can also be supplied. State when ordering

Can be bored for .130" (3.2mm)  or .150" (3.8mm) cable. Please state when ordering.

Longer or shorter lengths can also be supplied. State when ordering

Can be bored for .130" (3.2mm)  or .150" (3.8mm) cable. Please state when ordering.

OCTURA stub shaft 1/4" turned down to 3/16" with flats ground for securing connecting ferrule and 3/16" drive dog.

Aeromarine case hardened prop shaft. 4.25" x 1/4"  with 1/4unf thread.

<strong>Octura</strong> 4.5"  x 1/4" stainless steel prop shaft with flats milled for drive dog and ferrule grub screws.

Octura  S/steel 1/4" x 4.5" prop shaft complete with 7/16" OD. drive dog and brass prop nut. Shaft has flats milled to take drive dog and ferrule set screws.

Male & Female underwater U/J comprising of OC610F & OC610M units for coupling 3/16" to 3/16" shafts. Couplings are made from hardened plated steel with one grub screw in each

Female underwater u/j for joining 3/16" bore shaft from the engine to a 3/16" prop stub shaft. Plated hardened steel with one grub screw."

Male underwater U/j for connecting to a 1/4" prop stub shaft. Made from plated hardened steel with two securing grub screws.

Male underwater universal joint for connecting to 3/16" prop stub shaft. Plated hardend stell with two grub screws

Octura hardened male U/J joint with 3/16" bore and one fixing grub screw

Stainless steel 3/16" x 2.5" stub shaft with 5mm thread. drilled to take either .130" or .150" flexi cable. State bore when ordering
Please state when ordering if a longer shafts is required.

Octura 1/8" stainless steel stub shaft bored to take .098" cable

OCTURA brass connecting ferrule for connecting 3/16" cable to a 3/16" stub shaft

Octura brass connecting ferrule for connecting 1/4" cable to 3/16" stub shaft

OCTURA Brass connecting ferrule for connecting 1/4" cable to 1/4" stub shaft.
Cable has to be soldered to the ferrule which is then fitted to the stub shaft with 2 grub screws.

OCTURA 1/8" lead Teflon sleeve bushing

AEROMARINE 1/4" lead teflon sleeve bearing. <strong>SPECIAL OFFER. NSP. £2.40 per pack of 2