Our products

5mm nylock prop nut for 3/16" Flexi shaft

A strong fibreglass moulded radio box. This one is designed for use in deep vee's and slopes from 65mm at the back to 50mm deep at the front. Allowing for the use of a 1/4 scale servo and two standard size servos to be stood upright. The box measures 4.65 x 5.5" and comes with a plexi glass lid which sits in a lip around the top internal edge. The box is also available in a shallower design where heigth is limited and allows the servos to be laid on their side.
Another lid is available for use with "D" rubber section to seal the lid down, add an extra £3.50 for this version"

We now have the dealership in the UK for the distribution of BHHANSON products.

Engines, upgrade kits, exhausts, spares etc

21 Beta Evo Water cooled straight header with spring and seal

Standard plug head button fits RS & RSEvo

Mocom CNC prop 50mm diam. x 69mm pitch. This would be the nearest prop to the 1919. It would need to be trimmed down by a mm or two.

OCTURA hummdinger 4" wide engine mount with deep cradle, fits engines 3.5cc to between 4" stringers.

Special order only from manufacturer."

Octura stainless steel 3/16" long prop shaft with flats machined for location of drive dog and connecting ferrule

The smallest of the prather props in silicon bronze, ideal for 3.5cc engines.

Comparable to Octura X440

5mm x 6" Stainless steel shaft & tube

Steel pushrod 2mm diameter 300mm long. with one end threaded 2mm

Black standard length non fray starter belt 500mm x 5mm wide. Ideal for the .12 to .18 flywheels and some .21 engines.

Sullivan rigid polythene VT-16. 16oz shallow V tank for glow/petrol.
Needs conversion kit for petrol use
Size: length 168mm x width 93mm x heigth 45mm.

To convert Sullivan hard tanks for use with petrol. For greater fuel flow than the regular tube version.The bung is made from a high quality Flouroelastomer rather than rubber. Needs a short length of petrol fuel tube. Do not use on Flexitanks.

The Starter Handle has now been discontinued and is no longer being produced by the manufacturer. 

<strong>NEW<strong/>.Speedmaster high quality S/steel flexi shaft coupling 1/4unf to 3/16"
CMB45/21, OS45,K&B 45/65 etc. 

Speedmaster 3/16" SOLDERED flange brass bushing for 3/16" struts

Aluminium 3.2mm bore water outlet

Glass filled nylon X35 prop 5mm thread only.

Using a "X" blade pattern, these glass-filled nylon props have a much higher strength and rigidity than their nylon counterparts making them ideal for use with high power marine engines. Each prop features a moulded-in brass insert

The X5 series props have a reduced blade area very similar in profile to the prather props. Their pitch to diameter is a 1.5 : 1 Ratio. At present there are only three props in this series as the number of props in the X4, Y5, & X6 series more than accomodate the requirements needed by set ups.
Blade profile is the same as the Prather props.

The Zenoah G260 Marine is a powerfull and reliable petrol engine straight out of the box and ready to go. Fitted with a twin needle Walbro 644 carburettor its performance is quite outstanding for a petrol engine.

Ideal 3.5cc hydro SA and circuit racing prop. 38mm dia. x 2.85" pitch

Too much load with your X440, then try the M440"

 Ideal for fast electrics. Prop has a 1/8" bore which can be threaded 4mm. 30mm dia. x  1.65" pitch"

Large painted 3" size driver to fit hulls such as the 56" Apache and 60" Shead. 

High grade Stainless steel drive dog with s/s grub screw, 3/16" bore x 3/8" OD. for props with a 3/8" od. hub.

Octura flexi cable .130" (3.2mm) per 12". (305mm)