Our products

Caldercraft 12" x 5mm stainless steel prop shaft & 8mm tube

Kevlar non fray, standard length toothed belt giving good grip on the flywheel,  550mm x 6mm

Speedmaster high quality stainless steel easily adjustable tabs. 1" wide x 1.5" long.

USA import SPEEDMASTER Brass sleave flared bushings for the stinger drive units. 3/16 & 1/4". These are brass sleaves, crossed drilled to hold the lubricating grease."

Glass filled nylon X50mm prop with 5mm thread

Glass filled black nylon X55 with 4mm thread

Using a "X" blade pattern, these glass-filled nylon props have a much higher strength and rigidity than their nylon counterparts making them ideal for use with high power marine engines. Each prop features a moulded-in brass insert

Red nylon racing prop 55mm

Hansons most powerful Zenoah engine producing 5.9HP @ 17,000 rpm, with 5HP still being produced@ 18,000rpm. Engine will be customer set timing, depending on your application. Engine has 1mm stroker crankshaft,  M-cut lightweight piston with increased compression, enlarged inlet & exhaust port race timed, extensive transfer port modifications, trued & balanced crankshaft with bearings set for end play with low drag seals, bored out and bell mouthed 257 or 1048 carb. and balanced flywheel
As the engines are custom made delivery is approx. 2 weeks from the States.

Good 11cc rigger/hydro surface prop

10% more pitch than the X4 series. An ideal replacement for a X445 which will give more speed or an X447 if it is loading your motor too much.

Prop has a 1/8" bore which can be threaded 4mm. 32mm dia. x 1.67" pitch.

 

 

OCTURA Flexi Cable .150" (3.8mm) x 24" right hand lay cable for clockwise rotation of prop

Bobbin type coupling using 20mm x 15mm bobbin.

High grade Stainless steel drive dog, 1/4" ID x 7/16" OD with two s/s grub screw.

Heavy duty ball link for 3mm threaded rods

5mm Stainless steel stub shaft 2.5" long. Please specify actual length required and hole size for shaft.

Aeromarines medium sized Challenger 43" long with a 14" beam. Ideal for 6.5 to 7.5cc engines although for the ultimate speed fit a .67 UK Delivery charge £30.00  UK.

Stainless steel water outlet 3.2mm id. with nut and washer

Radio box rubber bung also suitable for saddle Tanks..

ABC Chopper2314-15-65(3) CPL heat racing prop. 2.3 dia x 3.22" pitch. 15deg. rake."

Aeromarine 30" x 3/16" flexi shaft. with case hardened stub shaft.

A good Hydro racing prop for strong .21 engines. 45.5mm (1.79") x 71mm (2.9" cupped) A good replacement for an Octura 1450

The famous OCTURA wedge rudder. Ideal for all size craft from 7.5cc up to 35cc. The rudder comes with two polycarbonate tiller arms, a pivot block, or a "T" bracket for transom mounting and has a large bore integral water pick up machined in the blade.

TO CLEAR
Silicon bronze prop 45mm diam.

Equivalent OCTURA prop  X445

14" x 5mm stainless steel prop shaft & 8mm S/steel tube

A resin half body, full helmet, scale driver, 2.5" to 3" high. Clear or grey. Suits the larger hulls like the Giant Apache & CUV Shead hulls. Drivers can be moulded shorter if required. 2.0" is ideal. Moulded in 5mm Bolt & nut."

SPEEDMASTER high quality Stainless steel trim plates 1" W x 1.5"L.
Ali bracket has single adjusting scew, all s/s nuts and bolts supplied
Pack of 4

We can split and sell as a pair if required at £11.25